Skip to content
Materials & Standards

Understanding Common Stainless Steel Grades

Austenitic, ferritic, martensitic and duplex grades are not points on a quality scale. They are different metallurgical families, and the right one depends on what the part must do.

Editorial TeamPublished 5 min read

“Stainless steel” describes a family of alloys, not a material. The differences between grades are metallurgical, and they change what a part can be made to do: whether it can be formed, welded, hardened, or exposed to chlorides.

This guide covers the main families and the grades that appear most often in industrial purchasing, with the mapping between regional standard systems that causes most of the confusion.

Four families, four behaviours

Family Structure Typical grades Distinguishing behaviour
Austenitic Face-centred cubic 304, 316, 321 Highly formable and weldable; not hardenable by heat treatment; non-magnetic in the annealed condition
Ferritic Body-centred cubic 430, 409 Magnetic; moderate formability; resistant to stress corrosion cracking; limited weldability in thick sections
Martensitic Body-centred tetragonal 410, 420, 440 Hardenable by heat treatment; high hardness and wear resistance; lower corrosion resistance
Duplex Austenitic + ferritic 2205, 2507 High strength; good chloride resistance; less formable; welding requires control

Choosing a family is the first decision, and it is driven by function rather than by price. A part that must be deep-drawn needs an austenitic grade. A blade that must hold an edge needs a martensitic grade. A shaft that must be hard and corrosion-resistant may need either a martensitic grade with a coating, or a different approach entirely.

The 300 series: the general-purpose austenitics

The 300 series contains the grades most industrial buyers will encounter.

304 is the baseline austenitic grade: formable, weldable, and adequate in most non-chloride environments. It accounts for the majority of stainless steel used in general fabrication.

316 adds molybdenum, which improves resistance to chloride pitting and crevice corrosion. It is the default for coastal, marine, chemical and chloride-bearing duties. The comparison with 304 is covered in detail in Stainless Steel 304 vs 316.

321 is stabilised with titanium to prevent chromium carbide precipitation at elevated temperature. It is used where the part operates hot enough for that mechanism to matter — exhaust components, some heat-treatment fixtures — and where welding in thick sections would otherwise risk sensitisation.

The L variants (304L, 316L) limit carbon to reduce the same sensitisation risk during welding. They are a welding specification more than a service specification.

The 400 series: hardenable and magnetic

410 is a general-purpose martensitic grade, hardenable by heat treatment and used for parts requiring moderate corrosion resistance with wear resistance — shafts, valve trim, cutlery-grade hardware.

420 carries higher carbon for greater hardness, used where wear resistance dominates.

430 is ferritic: magnetic, formable, and used for applications where deep drawing and moderate corrosion resistance are needed without the nickel cost — appliance panels, automotive trim, some architectural work.

These grades are frequently rejected in specifications that assume “stainless” means “304-like”. A buyer who specifies a 410 part and expects 304 corrosion performance will be disappointed, and the specification, not the supplier, is at fault.

Duplex grades: strength and chloride resistance

Duplex stainless steels have a mixed austenitic-ferritic microstructure. They offer significantly higher strength than austenitic grades and good resistance to chloride stress corrosion cracking, at the cost of formability and welding complexity.

They are used in applications where the combination matters: offshore equipment, desalination, chemical process vessels, and long-span structures where weight matters. Their welding requires controlled heat input and, usually, a specified filler, so a fabrication specification for duplex is not the same document as one for 304.

The 200 series: a cost-driven family

The 200 series substitutes manganese for part of the nickel in an austenitic structure. It is cheaper and is used widely in some markets for consumer goods and light fabrication.

For industrial purchasing, the important point is that 200-series material is not interchangeable with 300-series in corrosion performance, and it can be magnetic after forming. Where a specification says “stainless steel 304” and receives 200-series material, the part will look correct and behave differently. Verifying the grade is part of receiving inspection, not an optional extra.

Standards differ by region, grades map approximately

The same grade appears under different designations:

Common name ASTM / AISI EN JIS
304 304 1.4301 SUS 304
304L 304L 1.4307 SUS 304L
316 316 1.4401 SUS 316
316L 316L 1.4404 SUS 316L
430 430 1.4016 SUS 430
410 410 1.4006 SUS 410

These correspondences are approximate. Composition ranges differ slightly between systems, and a part that meets one standard may fall marginally outside another. For a critical application, the purchase specification should name the standard and the grade, not just the grade number, so that the supplier’s certificate can be checked against the requirement.

A mill certificate states the heat analysis and the standard it was tested against. It is the document that closes the gap between “we ordered 316L” and “we received 316L”, and it should be requested where the material matters.

Finish and thickness change the outcome

Two parts in the same grade can behave differently because of how they were finished and how thick they are:

  • Pickled and passivated surfaces restore the passive layer after welding. Heat tint, left in place, is a common starting point for corrosion.
  • Polished or bright annealed surfaces reduce sites where contaminants settle.
  • Thickness determines corrosion allowance. A grade selected correctly but supplied thin will have a shorter life than the same grade at full thickness.

A specification that states grade, standard and finish, with a tolerance on thickness, can be verified on receipt. One that states only “stainless steel” cannot.

What to put in a material requirement

  • Grade, with the standard system named.
  • Product form and dimensions, with thickness tolerance.
  • Surface finish.
  • Whether a mill certificate is required, and what it must state.
  • Welding and post-weld treatment requirements, if the part is fabricated.
  • Any restriction on substitutes, stated explicitly.

The stainless steel category page lists the fields we ask for before quoting. Where the material decision needs to be made against a specific service environment, specification and quality planning covers how that is structured, including what can and cannot be confirmed without testing.

Key Takeaways

  • The 200, 300 and 400 series describe metallurgical families, not grades of quality.
  • Austenitic grades are formable and weldable but not hardenable by heat treatment; martensitic grades are the reverse.
  • Duplex grades sit between austenitic and ferritic, trading formability for strength and chloride resistance.
  • Grade alone does not determine performance — finish, thickness and welding practice matter as much.

Product families and types covered by this guide. Each links to the specifications we ask for before quoting.

Where this topic turns into an actual order.

Product Comparisons

Stainless Steel 304 vs 316: When the Difference Matters

The two grades look identical, machine similarly and cost differently. The difference is molybdenum, and whether the application exposes it to chlorides decides if that cost is necessary.

Read article5 min read
Technical Guides

Understanding Industrial Bearing Specifications

What the numbers and suffixes on a bearing designation actually mean, where the boundary of the designation sits, and which execution details it does not cover.

Read article5 min read
Industrial Procurement

How to Prepare an Industrial RFQ

An RFQ is not a request for a number. It is the document that determines whether the quotations you receive can be compared — or only sorted by price.

Read article6 min read

Need help sourcing industrial products from China?

Tell us your product requirements, specifications and purchasing needs. We can help you explore suitable sourcing options from China's industrial supply chain.

We reply within 1 business day — from a named person, not an auto-responder. Your requirement is confirmed first; the quotation follows once details are agreed.