Skip to content

Materials & Fabrication

Metals & Industrial Materials

Metal is bought by grade, and grade is where international trade goes wrong most often. GB/T 700 Q235B, ASTM A36 and EN S235JR are broadly similar structural steels, but they are not the same specification, and a mill certificate issued against one does not demonstrate compliance with another. When a drawing says "mild steel" the mill will supply what is customary in its own market, which may not be what your engineer assumed.

Beyond grade, three fields decide whether material is usable: the mill certificate and its type, the dimensional tolerance, and the condition or temper. A 3mm plate rolled to a wider tolerance than your process allows will cause fit-up problems that look like a fabrication error. We put tolerance and condition on the inquiry alongside the grade.

China's steel capacity is concentrated in Hebei, Jiangsu and Shandong for flat and long products, with stainless and speciality grades in Shanxi, Zhejiang and Guangdong. Availability of a specific grade in a specific thickness is genuinely variable, so we quote what is rollable against what is in stock rather than promising a single lead time.

Category at a glance

Metals & Materials

Product types mapped
7
Dedicated sub-pages
1
Reply commitment
1 business day

We supply to your specification. We do not manufacture this category and we do not inspect goods — how quality risk is handled is set out separately.

  • 15 product familiesone purchase order
  • Exported from NingboEXW / FOB / CIF / DDP
  • One specification sheetquoted line by line
  • Reply in 1 business dayfrom a named person
Start your sourcing project →

Coverage

What this family covers

Everything below is supplied, whether or not it has its own page. Linked items have a dedicated page with their own specification detail.

Steel ProductsStructural sections, plate, bar and coil.
Stainless Steel304 / 316L sheet, tube, bar and fittings.
Aluminum ProductsExtrusion, sheet, plate and machined profiles.
Copper & BrassBusbar, tube, rod and machined brass parts.
Metal ProfilesCustom and standard profiles, roll-formed shapes.
Metal Sheets & PlatesHot and cold rolled sheet, cut or sheared.
Industrial AlloysTool steel, heat-resistant and wear alloys.

Not listed? The category boundary is a sourcing convenience, not a limit. Describe the item and we will tell you whether it fits.

Specification

What to write down before you ask for an offer

These are the fields that move a metals & materials quotation. You do not need all of them to start an inquiry — but each one you leave out comes back as an assumption, and the assumption will be the factory's, not yours.

Send these details
  1. 01

    Grade and standard

    ASTM, EN, JIS or GB number, not a description such as "mild steel" or "304".

  2. 02

    Form and dimensions

    Plate, sheet, bar, coil, tube or profile, with thickness, width and length.

  3. 03

    Tolerance class

    Thickness and flatness tolerance, which changes with mill and product form.

  4. 04

    Condition

    Hot rolled, cold rolled, annealed, quenched and tempered, 2B, BA, No.1 finish.

  5. 05

    Certificate type

    EN 10204 2.2 or 3.1, and whether heat number traceability to the piece is required.

  6. 06

    Testing

    Tensile, impact at a stated temperature, hardness, or intergranular corrosion for stainless.

  7. 07

    Cutting and edge condition

    Mill edge, slit, sheared, laser cut or sawn, and the edge quality needed.

  8. 08

    Surface protection

    Pickled, oiled, PVC-coated, or bare with interleaving for transport.

Where it goes wrong

What actually causes problems in this category

Specific to metals & materials, not generic advice. Each of these is something we ask about before a factory is approached.

Grade equivalence is approximate, not exact

Published equivalence tables compare chemistry ranges, not guaranteed properties. Q235B and A36 differ in silicon and in the guaranteed yield at thickness. Where the material carries structural or pressure duty, the grade should be specified in the standard your engineer designed to, and the certificate should match that standard — not a cross-reference table.

The certificate type is part of the order

A 2.2 certificate is a declaration by the mill against its own test; a 3.1 certificate is issued with specific test results traceable to the heat. Only 3.1 is normally accepted for pressure or structural work. Asking for 3.1 after the material has been cut and shipped is not possible, which is why it belongs on the inquiry.

Tolerance is a specification decision, not a footnote

Plate rolled at the low end of the thickness tolerance is lighter per square metre, which matters if you are buying by area and fabricating to a design thickness. We state the tolerance class and, where the application is thickness-critical, ask for the actual measured thickness on the certificate rather than the nominal.

Freight geometry decides whether it arrives intact

Coil, plate and 12-metre bar have very different freight profiles, and overweight containers are a real constraint on steel. An offer that looks simple per tonne but needs a flat rack or an overweight surcharge is not simple. We check weight and dimensions against container limits before confirming.

Common questions

Metals & Materials — asked often

Answers include what we cannot do, where that is the honest answer.

Can you supply material to a European grade with a 3.1 certificate?

Where a Chinese mill produces that grade and issues the certificate, yes. Some EN grades are routinely rolled for export; others are only available as a near-equivalent GB grade, which is not the same thing. We tell you which case applies before you order rather than presenting an equivalent as compliant.

Do you supply small quantities of metal?

Small quantities are possible for sheet, bar and tube through stockists rather than in mill quantities. Plate and coil are mill-order products with real minimums. We state the minimum for each line so you can see where consolidating several items into one order changes what a single shipment can cover.

Can material be cut to size before shipment?

Yes, and cutting at source is usually more accurate than cutting on site, as well as reducing freight volume. Tolerances on cut dimensions are wider than machined tolerances, so if the parts are to be machined afterwards we ask for a stock allowance to be left. Cut material is not returnable, so the cut list should be confirmed before production.

How do I verify the grade actually supplied?

Through the mill certificate and, if the risk justifies it, independent testing. We provide the certificate the mill issues and we check that the heat numbers on it match the marking on the material. We do not operate a laboratory and we do not authenticate material — where verification matters, that is a test you commission from a third party.

Metals & Materials from China, priced and shipped

Send the specification, a drawing, or a photograph of the part you are replacing. A named person replies within one business day — with what we can confirm and what we still need from you.

We reply within 1 business day — from a named person, not an auto-responder. Your requirement is confirmed first; the quotation follows once details are agreed.