Skip to content
Technical Guides

Understanding Industrial Bearing Specifications

What the numbers and suffixes on a bearing designation actually mean, where the boundary of the designation sits, and which execution details it does not cover.

Editorial TeamPublished 5 min read

A bearing designation such as 6205-2RS C3 looks precise. It is precise about some things and silent about others, and the silent part is usually what determines whether the part works in the application.

This guide explains what a standard designation contains, what it does not, and how to close the gap when writing a requirement.

What the base number encodes

Under the international dimension plan for rolling bearings (ISO 15), a standard designation carries three pieces of information in sequence:

1. Bearing type. The leading digit or letter identifies the family — deep groove ball, angular contact, cylindrical roller, tapered roller, spherical roller, needle, thrust, and so on. This is what tells you whether the part can take axial load.

2. Dimension series. A two-digit combination of width and diameter series. It expresses how heavy the bearing is for a given bore — a light series, a medium series, a heavy series. Two bearings with the same bore but different dimension series have different outside diameters and different load capacity.

3. Bore code. For bores of a certain size and above, the last two digits multiplied by five give the bore in millimetres. A designation ending in 05 corresponds to a 25 mm bore; ending in 20, to 100 mm. Below that threshold the code follows a separate rule, and small bores should be checked against a table rather than assumed.

Reading a designation this way takes a few seconds and prevents a common purchasing error: substituting one dimension series for another because the bore matched.

What the base number does not encode

This is the part that causes the majority of specification disputes. The base number says nothing about:

  • Tolerance class. Normal, P6, P5, P4 and higher classes define progressively tighter dimensional and running accuracy. A P5 bearing and a normal bearing with the same number are not the same product, and the price difference reflects that.
  • Internal clearance. Normal clearance, C3, C4 and reduced-clearance variants are different executions. Clearance is consumed by interference fits and thermal expansion, so the correct value depends on the installation, not on preference.
  • Cage type and material. Pressed steel, machined brass, polyamide and other cage designs behave differently under speed, temperature and vibration. Cage selection is a technical decision that is frequently left to the supplier’s default.
  • Sealing or shielding. Open, shielded and sealed variants are separate executions. The suffix differs, and so does the friction and the allowable speed.
  • Lubricant. Where a bearing is supplied pre-greased, the grease quantity, base oil and thickener are part of the specification but rarely appear in the designation.
  • Noise or vibration grade. Applications sensitive to running noise often require a specific vibration grade, which is a separate classification.

Each of these is a real specification dimension. A designation that omits them is not wrong — it is incomplete, in the same way a car model name does not specify the tyres.

Suffixes are where the specification lives

Suffixes carry the execution information:

Suffix family What it indicates
ZZ / 2Z Shielded on one or both sides — contact-free, excludes coarse contamination
2RS / 2RS1 Contact seal on both sides — retains grease, excludes liquid and fine dust
C2, CN, C3, C4 Internal clearance, from reduced to increased
P6, P5, P4 Tolerance (accuracy) class
N, NR Snap ring groove, with or without ring
TN9, M, J Cage designation — polyamide, brass, pressed steel

Two cautions about suffixes:

  1. They are not fully standardised across manufacturers. Some suffixes are widely used and understood; others are manufacturer-specific. A suffix that one factory uses for a brass cage may mean something else elsewhere.
  2. Suffix order and combination matter. 6205-2RS C3 and 6205 C3 2RS describe the same execution. 6205-2RS and 6205 ZZ do not, even though both are sealed against something.

This is why a purchase requirement should state the execution in words as well as in a designation. The words survive a change of manufacturer; the designation may not.

Where standards fit

Standards define the framework rather than the part:

  • Dimension plans define the boundary dimensions that allow interchangeability across manufacturers. This is why a 6205 from one factory fits a housing designed for a 6205 from another.
  • Tolerance standards define what each accuracy class means in measurable terms.
  • Load rating and life calculation standards define how basic dynamic load ratings are calculated and how life is estimated from load and speed.

A standard does not certify a specific bearing. A supplier claiming compliance is claiming that the part is manufactured within the defined tolerances — which is verifiable by measurement, and worth asking about when the application is sensitive.

Converting a designation into a requirement

A specification that can be quoted without assumptions looks like this:

  • Designation, or the boundary dimensions if no designation exists.
  • Tolerance class, stated explicitly.
  • Internal clearance, stated explicitly, with the reason if it differs from normal.
  • Cage type and material.
  • Sealing arrangement.
  • Lubricant, if pre-greased — type and fill.
  • Noise or vibration grade, if applicable.
  • Standard to which the part must be manufactured, and whether an inspection record is required.

An enquiry that lists all of the above will receive quotations that can be compared. An enquiry that lists a part number will receive quotations that all look the same and are not.

Common mistakes

  • Assuming the number fixes the execution. It fixes the dimensions and the family, not the grade.
  • Substituting a suffix. A 2RS is not a ZZ with a seal added; the friction, speed limit and sealing behaviour differ.
  • Comparing prices across tolerance classes. A P6 part priced against a normal-class quotation is not a cheaper alternative; it is a different product.
  • Leaving clearance to the supplier. The correct clearance depends on the fit and the thermal condition, both of which belong to the buyer.
  • Trusting a suffix without a written description. Suffix conventions are not universal.

If the execution is settled and the task is finding a supplier who holds it consistently, the bearings category lists the fields we ask for before quoting. For the selection process itself — load, speed, clearance and sealing in application terms — see How to Choose Industrial Ball Bearings.

Key Takeaways

  • A standard bearing designation encodes type, dimension series and bore — not tolerance class, clearance, cage, seal or lubricant.
  • The bore code follows a rule: two digits multiplied by five gives the bore in millimetres, above a threshold.
  • Suffixes are where suppliers diverge; two bearings with the same base number can differ in clearance, cage and sealing.
  • A specification is complete only when the execution details are written out, not implied by the base number.

Product families and types covered by this guide. Each links to the specifications we ask for before quoting.

Where this topic turns into an actual order.

Industrial Applications

Bearing Selection for Electric Motors

An electric motor loads its bearings in ways the shaft drawing does not show: magnetic pull, thermal growth along the shaft, and shaft currents on driven equipment.

Read article5 min read
Technical Guides

Understanding Pump Head, Flow Rate and Pressure

Head, flow and pressure are three different quantities that get used interchangeably. The difference decides whether a pump is correctly specified or merely correctly priced.

Read article5 min read

Need help sourcing industrial products from China?

Tell us your product requirements, specifications and purchasing needs. We can help you explore suitable sourcing options from China's industrial supply chain.

We reply within 1 business day — from a named person, not an auto-responder. Your requirement is confirmed first; the quotation follows once details are agreed.