Sourcing & export service
Supplier Comparison & Offer Analysis
Supplier offers use different assumptions and formats. A useful comparison makes those differences visible before you place an order.
Three quotations for the same item are rarely three descriptions of the same thing. One includes packing, one excludes it, one quotes a lower material grade, one assumes your annual volume, one has priced tooling separately. Comparing the headline figure across those offers produces a decision that is arithmetically correct and commercially wrong.
Our work is to remove the differences that are not real, so that the remaining difference is the one you are actually deciding on. That means one specification sheet, one incoterm basis, one packing assumption, and a written list of what each supplier excluded — because exclusions are where quotations turn into disputes.
Stage
Supplier Comparison
Who it is for
- Buyers holding several offers and unsure which describes the product they need
- Teams whose supplier has drifted from the original specification without saying so
- Projects where technical equivalence between offers is not obvious
Applied to these categories
Deliverables
What you receive
These are documents and answers, not promises. If any of them is not produced, that is a failing on our side and should be raised as one.
- 01
One specification sheet all suppliers quote against, with deviations flagged line by line
- 02
Every offer read against that sheet, so a difference points to a real difference in the product rather than a difference in what each factory assumed
- 03
Comparison on the same basis of delivery and the same exclusions, so the numbers describe the same delivery
- 04
Written note on what each supplier excluded — the most common source of later disputes
How it runs
The stages, in order
Each stage produces something you can read or check. That is the point of separating them — a stage with no output is a stage nobody can hold to account.
- 01
Build the comparison basis
A single specification sheet with the material, tolerance, finish, packing and testing stated once. Every supplier quotes against the same document, and any deviation they propose is recorded rather than absorbed.
- 02
Decompose the offer
Where suppliers disclose it, the offer is broken into material, process, tooling, packing and freight. A difference in one component explains the rest, and that explanation is what makes a conversation possible.
- 03
Compare landed, not ex-works
Freight, packing density, duty basis and lead time all move the total. A simpler ex-works offer on bulky goods can be the worse landed option, and the comparison should show that before you decide.
- 04
Write down the exclusions
Each offer gets a note on what it does not include. Ninety per cent of the arguments we see after an order are about something that was never in the offer, not about quality.
Boundaries
What this service does not include
Stated here rather than discovered later. If any of these is essential to your programme, it needs a different arrangement — and we would rather plan that with you at the start than explain it after a shipment.
Full quality & risk statementWe do not audit a supplier's internal figures or verify that a disclosed breakdown is accurate. We report what they state.
We do not claim that the smallest figure is the best commercial choice. That depends on risk tolerance, which is yours to set.
We do not test or measure samples to confirm technical equivalence. Where equivalence is claimed rather than documented, we mark it as a claim.
Common questions
Supplier Comparison — asked often
I already have three quotations. Can you just analyse them?
Yes. Send them with the specification they were quoted against, and we will normalise them onto one basis and flag the differences that are real. If the quotations were made against different specifications, part of the work is reconstructing a common basis — which is often where the real difference between the offers becomes visible.
What if a supplier will not disclose a breakdown?
Many will not, particularly for commodity items where the process is simple. In that case we compare on the components that are visible: material grade, weight, process route, packing and lead time. Non-disclosure of a breakdown is not automatically a red flag, but it does limit how precisely a difference between offers can be explained.
Can you negotiate with the suppliers on my behalf?
We can put your target and the reasoning in front of them, and report what they say. What we will not do is pretend a lower figure was achieved by pressure when it was achieved by removing something from the specification. If a supplier changes material or tolerance to reach a number, that is a change you should approve explicitly, not a concession.
Where it applies
Industries that use this most
Next stage
Talk to us about supplier comparison
Tell us where your project stands and what you have already tried. A named person replies within one business day, including when the honest answer is that this service is not what you need.
We reply within 1 business day — from a named person, not an auto-responder. Your requirement is confirmed first; the quotation follows once details are agreed.